Mid Month Potholders- bowties

midmonth potholders

I’m sure you’ve seen the new bowtie dies from accuquilt, or rather the updated Companion corners sets!

GO! Qube 8" Companion Set-Corners (55785)

At first I was playing in EQ with the bowtie block to see what I’d come up with. The 6” QUBE set, makes 3” bow ties, so a 3 x 3 layout would be 9” finished.

bowtie3 in9in

if it’s a 2×2 layout and then a border it would be 8” or so –depending on the border size

with a 8” set (4” bowties) and a 2×2 layout, would be 8” without a border or more with a border.

With the 9” set, it would be 9” without a border.

with the 12” I’d probably just make one bow tie and add a border

bowtie3 in8in

I decided on this layout with the 6” set and adding a border.

I decided to make 4 matching blocks so the front and back of the potholders are the same!

I used 3 FQs plus 1 for the border and then yardage for the binding.

For each block I cut out (4)  #2 squares from 2 grey and black FQs, so 16 total, and the small triangles too (11.2)

IMG_20180502_182302581

Then in white I cut out (8) of 11.1 bowtie backgrounds (32 total)

IMG_20180502_182715532_HDR

These block pieces are so cute and tiny!!

IMG_20180502_183207442_HDR

I also cut strips in black with my 1 1/2” strip die

Since I’d use it for the sides, one set would be trimmed to 6 1/2” and the other 8 1/2” so I folded and cut on the short width of the FQ (18”) and cut out 8 strips.

IMG_20180502_183534177

Then I sewed the small triangles to the white backgrounds and ironed the seams open. (16 each)

IMG_20180503_095803106

Then added the squares and also ironed the seams open

IMG_20180503_100941414_HDR

and finished the bowtie blocks. (8 each)

IMG_20180503_101649403_HDR

and I sewed them together into blocks like this, I also made the hanging tag from the leftover black. I’ve shown before how I made those.

IMG_20180503_102326456_HDR

Then added the borders

IMG_20180503_103414732_HDR

I then laid out two of then on insulbright and 2 on batting scraps and quilted in the ditch in black and also on the outer edge.

IMG_20180503_142916689

I then decided to add binding on these and since the edges are 8 1/2” x 4, ONE WOF strip worked just great!

I first pinned the layers together and actually had the back piece rotated 90 degrees, I also pinned the hanging strips and then basted close to the edge all the way around BEFORE adding the binding

IMG_20180503_143211612_HDR

I never do this binding technique much anymore, but this time I folded over one raw edge before ironing the strip in half, so when I sewed the binding on, the end gets trimmed and tucked into the folded edge.

IMG_20180503_144028441_HDRIMG_20180504_080036085_HDR

and I hand stitched down the binding onto the back.

That’s it Smile cute modern potholders

IMG_20180504_091358509

Hope you make some!

Two people made last month’s potholders, aren’t they both cute??

pamelaaprilmay

FB_IMG_1525378286187

1 thought on “Mid Month Potholders- bowties”

  1. Cheryl's Teapots2Quilting

    I made a bow tie quilt for my inlaws, when I first started quilting. It had Y seams. I didn't realize that there were easier ways to make it. I've since learned easier ways. You've been a busy bee. Sorry, I'm trying to catch up on blog reading, and just read all your posts since the beginning of the month.

Comments are closed.

Shopping Cart